View Cart “Pacific G1/4 45 & 90 Degree Adapter – Chrome” has been added to your cart.
Pacific C-PRO G1/4 PETG Tube 16mm OD Compression – Red (6-Pack Fittings)
Pacific C-PRO G1/4 PETG Tube 16mm OD Compression – Red (6-Pack Fittings)Pacific C-PRO G1/4 PETG Tube 16mm OD Compression – Red (6-Pack Fittings)Pacific C-PRO G1/4 PETG Tube 16mm OD Compression – Red (6-Pack Fittings)CL-W214-CU00BL-B_9abc93e42ca1416199adce43e9520f5fCL-W214-CU00BL-B_d22a744a413e4a688afe77a8ee186d50

Thermaltake Pacific C-PRO G1/4 PETG Tube 16mm OD Compression – Red (6-Pack Fittings)

$59.99

The Pacific C-Pro Series is a revolution in fitment design. It simplifies the process of setting up a liquid-cooling loop and provides a seal that outperforms traditional compression fittings. By using 4 preinstalled O-rings and an overhauled design, the C-Pro Series is the new standard in fitment technology and it is exclusive to Thermaltake.

In stock

Product Description

Thermaltake Pacific C-Pro PETG Fittings Installation Guide

Step 1. Slide the compression nut over the tube
Step 2. Install the o-ring
Step 3. Install the packing
Step 4. Install the fitting base on your components
Step 5. Tighten the compression nut

Caution: The O-ring and the packing with a groove on the inside diameter must always be installed towards the top of the compression nut.

Caution

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks

  1. To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
  2. Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
  3. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
  4. Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup

  1. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
  2. Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
  3. DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
  4. Fill the reservoir to the top as it will prevent air from going into the pump
  5. If necessary tilt the system slightly from side to side to bleed the air out of the loop.
  6. Place some paper towels under fittings and joining points to test for leaks.
  7. Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop
  8. Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
  9. Coolant might fade over time.

* Specifications are subject to change without notice.
* The product picture(s) is only for your reference, it may differ from the actual product.

Additional Information

Weight 2 lbs
Dimensions 5 x 5 x 5 in

Reviews

There are no reviews yet.

Be the first to review “Thermaltake Pacific C-PRO G1/4 PETG Tube 16mm OD Compression – Red (6-Pack Fittings)”